Manual kia optima 2014

[Inberg]

.
.
Download / Read Online Manual kia optima 2014 >>
http://www.ejk.store9.su/download?file=manual+kia+optima+2014
.
.
.

<br>
<br>
<br>
<br>
<br>
<br>
<br>
<br>
<br>
<br>
.
Top element. For warranty details, visit R Recloser Control enclosure is excluded from the product warranty. The descriptions of SHO L and SHO T now mention the availability of eight additional latch, local, and remote bits and display points. Updated firmware version information. Added note to the TAR R command explanation that the target LEDs no longer reset if a TRIP condition is present. SYNCP accounts for the constant angle difference between reference voltage input VA and synchronism check voltage input VS. Current Directional Element for Neutral Ground Overcurrent Elements Figure 4. Routing of Directional Element to Neutral Ground Overcurrent Elements Figure 4. Corrected the designation for the ECLASS setting in Table H. EZ settings are active for a particular settings group. Breaker Monitor, Metering, and Load Profile Functions. Undervoltage Block for Frequency Elements . R Recloser Control operate as a recloser control. R Recloser Control provide more settings information and settings variation details. The associated overcurrent element settings listed in Table 1. The factory default SEL control equations OGIC settings are explained in the remainder of this section. Phase current input channels IA, IB, and IC are rated 1A nominal. Current input channel IN is rated 0. SV6T propagates to the logic in Figure 1. SEF overcurrent elements, respectively. Note the symmetry between Figure 1. The shot counter increments just before each reclose. R to the recloser, 120 Vac power, and power system voltages. R relay module is dead and the AC SUPPLY LED is extinguished anyway. The AC SUPPLY LED may flicker at times when tripping or closing, due to the battery momentarily discharging a bit. LED operation and logic operation. LOCK operator control pushbutton. Note the need to press the LOCK operator control pushbutton continually for three seconds until Relay Word bit PB5 asserts to logical 1 for one processing interval. TRIP pushbutton and a pending trip can be turned off by pressing the CLOSE pushbutton. R, both RECLOSER CLOSED and RECLOSER OPEN LEDs extinguish, even if the recloser is open. Relay Word bit PB8 functions in a manner similar to Figure 1. GROUND ENABLED operator control. Relay Word bit PB1 can propagate on to latch LT1. AUX 1 operator control pushbutton output to hot line tag logic. Inputs, Outputs, Timers, and Other Control Logic. R is powered down and then powered up again, i. Password and Breaker Jumper Operation. Serial Port Voltage Jumper Positions for Standard Relay Shipments . R Relay Module Inputs, Outputs, and Communications Ports. Date Code 20020215 Additional Installation Details. Refer also to Figure 19 in the guide. Often more than one alarm output contact is needed for such applications as local or remote annunciation, backup schemes, etc. An extra alarm output contact can be had without the addition of any external hardware. ALARM output contact in a standard relay shipment. Serial Port Communications and Commands for EIA 232 serial port pin functions. Reassemble the relay as described in the same subsection. Overfrequency Element Operation. Underfrequency Element Operation. Frequency Element Voltage Control. Other Uses for Undervoltage Element 27B81. Phase Instantaneous Overcurrent Elements . R Recloser Control Nondirectional Instantaneous Overcurrent Element Pickup Time Curve. R Recloser Control Nondirectional Instantaneous Overcurrent Element Reset Time Curve . Undervoltage Block for Frequency Elements. Levels 1 Through 6 Frequency Elements . Serial Port Communications and Commands for a list of the factory default settings. R Recloser Control Nondirectional Instantaneous Overcurrent. Pickup and Reset Time Curves See Figure 3. The different levels are enabled with the E50G enable setting, as shown in Figure 3. Besides the settings involved with the Torque Control Switch operation in Figure 3. Date Code 20020215 Overcurrent, Voltage, Synchronism Check, and Frequency Elements. Directional Control Option Refer to Figure 3. P1T is enabled and nondirectional. N1T is defeated and nonoperational, regardless of any other setting. G1T is defeated and nonoperational, regardless of any other setting. I and like settings and Relay Word bits. QT is defeated and nonoperational, regardless of any other setting. Voltage V is used in the synchronism check elements described in the following subsection Synchronism Check Elements. Voltage V is also used in the three voltage elements described at the end of Table 3. The angle settings are checked for synchronism check closing. R Recloser Control for more information on setting SYNCP with an angle setting. Synchronism Check Elements Operation Refer to Figure 3. Voltage Window Refer to Figure 3. Relay Word bits 25A1 and 25A2 in Figure 3. For various connections, Figure 1. Note that pickup settings 81D1P through 81D6P are compared to setting NFREQ. Relay Word bit 81D1T asserts to logical 1 only after time delay 81D1D. Convert Power Factors to Equival filexlib.
.
Manual kia optima 2014 bedienungsanleitung <br> Manual kia optima 2014 kezikonyv<br>Manual kia optima 2014 handbok <br> Manual kia optima 2014 guide<br>Manual kia optima 2014 podrecznik

[投稿者]

投稿